The toggle switch is divided into a small current toggle switch and a large current toggle switch. Small current toggle switches are often used in electronic toys, digital communications. Large current is generally used in electrical appliances, machinery and so on.

拨动开关主要广泛用于:各种仪器/仪表设备，各种电动玩具，传真机，音响设备，医疗设备，美容设备，等其它电子产品领域！

The switch is widely used in all kinds of instruments / instruments, all kinds of electric toys, fax machines, sound equipment, medical equipment, beauty equipment, and other electronic products.

额定功率：DC50V 0.3A

Rated power: DC50V 0.3A

工作温度范围：-20 ℃~60℃

Working temperature range: -20 C ~60 C

拨动开关各方面性能：

Switch all aspects of the switch performance:

一.电气性能规格

I. electrical performance specifications

1.接触电阻测试：

1. contact resistance test:

在微小电流（100mA）以下测试。

Test under small current (100mA).

要求：必须达到30毫欧以下。

Requirement: it must be under 30 millieu.

2.绝缘电阻测试：

2. insulation resistance test:

输入500V DC电压1分钟,按以下接触方法测试:

Input 500V DC voltage for 1 minutes. Test according to the following contact method:

(1) 接触端子之间.

(1) the contact terminals.

(2) 胶座体与排脚之间.

(2) between the pedestal and the foot.

要求：必须达到100兆欧以上.

Requirement: more than 100 megabux must be reached.

3.耐电压测试：

3. voltage tolerance test:

输入AC 500V（50-60Hz)电压，1分钟感度电流为0。5mA，按以下接触方法测试：

Input AC 500V (50-60Hz) voltage, 1 minutes sensitivity current is 0. 5mA, test according to the following contact method:

（1）排脚相互之间

(1) between the feet

（2）排脚与外壳之间

(2) between the feet and the outer shell

要求：没有绝缘破坏等异常.

Requirements: no insulation damage and other anomalies.

二.机械性能规格

Two. Mechanical performance specifications

1.动作力常规为：250+_50gf

1. the routine action force is: 250+_50gf

2.端子强度

2. terminal strength

在任意一个方向的先端上加力度(500gf)1分钟.

In any direction, increase the strength (500gf) for 1 minutes.

在排脚中没有裂开,菘动等异常,

There are no cracks in the feet, the Isatis and other abnormity,

要求：满足于机械,电器性能.

Requirements: meet the mechanical, electrical performance.

3.测试标准状态

3. test standard state

在没有指定的情况下测试温度、湿度、气压如下：

The temperature, humidity and pressure of the test are not specified:

(1) 温度为5℃~35℃

(1) the temperature is 5 ~35 centigrade.

(2) 湿度为45%~85%

(2) the humidity is 45%~85%

(3) 气压为80Kpa~106Kpa

(3) the pressure is 80Kpa~106Kpa

三.耐久性

Three. Durability

1.可焊性试验

1. weldability test

端子顶部被浸入锡焊池中1㎜深,温并为230±5℃,时间为3 ±0.5秒.

The top of the terminal is immersed in the tin solder pool 1 deep, the temperature is 230 + 5 degrees, the time is 3 + 0.5 seconds.

注意：

Be careful：

（1）焊接时间应少于3秒

(1) the welding time should be less than 3 seconds

（2）焊接面积要有80%以上.

(2) the welding area should be more than 80%.

2.耐焊性试验

2. resistance resistance test

焊炉焊接的时候温度控制在260±5℃，过炉时间为3±0.5秒,于基板厚度为1.0㎜

The temperature of the welding furnace is controlled at 260 + 5 degrees, and the furnace time is 3 + 0.5 seconds. The thickness of the substrate is 1.

手焊接的时候温度需控制在320±5℃,时间为3±0.5秒.

When hand welding, the temperature should be controlled at 320 + 5 C, and the time is 3 + 0.5 seconds.

要求：必须满足本体无变形,满足于机械、电气能.

Requirements: we must meet the requirements of ontology without deformation, and satisfy mechanical and electrical energy.

3.寿命测试

3. life test

无负荷：操作者以每分钟60次的频率作100，000回之无负荷测试。

No load: the operator performs the 100000 load test at a frequency of 60 times per minute.

要求：

Requirement：

(1)接触电阻不能超于200mΩ

(1) the contact resistance can not exceed 200m Omega

(2)其它、满足于机械、电器性能.

(2) others are satisfied with mechanical and electrical properties.

4.耐热试验

4. heat resistance test

放置在温度85±2℃中测试96小时后,再放置正常室温中1小时来测定.

After testing for 96 hours at a temperature of 85 + 2 centigrade, it was placed at normal room temperature for 1 hours.

要求：外观无异常驻,满足于机械,电器性能.

Requirements: no abnormal appearance, satisfied with mechanical and electrical properties.

5.耐冷试验

5. cold tolerance test

放置40±2℃。的相对湿度为90~96%环境中96小时后，

It was placed at 40 + 2 degrees C. The relative humidity was 96 hours after the 90~96% environment.

再将样板放在正常环境1小时后进行测试。

The samples were then tested in a normal environment for 1 hours.

要求：外观无异常,满足于机械,电器性能.

Requirements: no abnormal appearance, satisfied with mechanical and electrical properties.

6.潮湿试验

6. humid test

放置40±2℃。的相对湿度为90~96%环境中96小时后，

It was placed at 40 + 2 degrees C. The relative humidity was 96 hours after the 90~96% environment.

再将样板放在正常环境1小时后进行测试。

The samples were then tested in a normal environment for 1 hours.

要求：外观无异常,满足于机械,电器性能.

Requirements: no abnormal appearance, satisfied with mechanical and electrical properties.

应用范围

Application scope

1.影音产品：MP3、MP4音响；

1. audio and sound products: MP3, MP4 sound;

2.数码产品：数码相机、数码摄像机等；

2. digital products: digital cameras, digital cameras and so on;

3.通讯产品：手机、车载话机、电话机、楼宇设备、PDA等；

3. communication products: mobile phone, car phone, telephone, building equipment, PDA, etc.

4.安防产品：可视对讲机、监视器等；

4. security products: visual interphone, monitor and so on;

5.玩具：电子玩具等；

5. toys: electronic toys and so on;

6.电脑产品：摄像头等；

6. computer products: camera and so on;

7.健身器材：电子人体脂肪秤、跑步机等；

7. fitness equipment: electronic body fat scales, treadmills and so on;

8.医疗器材：血压计、体温计、医院呼叫系统等。

8. medical equipment: sphygmomanometer, thermometer, hospital call system and so on.